主动轴衬套孔与从动轴孔磨损的修理:主动轴衬套孔磨损后，可用铰削方法消除磨损痕迹，然后配用加大至相应尺寸的衬套。从动轴孔磨损也以铰削法消除磨损痕迹，然后按铰削后孔的实际尺寸配制从动轴NXQ2-L100/31.5-H
NXQ2-L150/31.5-H
蓄能器NXQ2-F0.25/10-H
NXQ2-F0.4/10-H
NXQ2-F0.63/10-H
蓄能器NXQ2-F1/10-H
NXQ2-F1.6/10-H
NXQ2-F2.5/10-H
蓄能器NXQ2-F4/10-H
NXQ2-F6.3/10-H
VT-VRPA1-527-1X/V0
VT-VRPA1-527-1X/V0/PV
VT-VRPA1-537-1X/V0/PV
VT-VRPA1-100-1X/V0/0
VT-VRPA1-150-1X/V0/0(2FRE6 )
VT-VRPA1-151-1X/V0/0 (2FRE10/16)
VT-SWKD-2-1X/V0/0
VT-SR42-1X/1/2
VT-SR42-1X/1/3
VT-KRRA2-537-2X/V0
VT-KRRA2-527-2X/V0/2
泗洪A11VLO260DRL/11L-NSD12N00 VT-VRPA1-527-2X/V0/RTS-2STV
VT-MSPA1-525-1X/V0
VT-VSPA1K-1-1X/
VT-MSPA1-50-1X/V0/0-24
VT-MSPA1-50-1X/V001
VT-MSPA2-1-1X/V0/0
VT-MSPA2-200-1X/V0/0
VT3002-2X/48F
VT3002-2X/64G
http://www.qihuiwang.com/product/q35527/253206799.html VT-SSPA1-508-2X/V0
VT-SSPA1-508-2X/V0/I
VT-SSPA1-525-2X/V0
VT-SSPA1-50-1X/V0/0-24
VT-PVPQ1-1X/2R900070872
VT-VPCD-1-1X/V0/1-P-1
VT-VPCD-1-1X/V0/1-D-1
VT-VPCD-1-1X/V0/1-C-1
VT-VPCD-1-1X/V100/1-0-1
枞阳A11VLO260EP2D/11L-NZD12N00H

3、油泵内部零件磨损

油泵内部零件磨损会造成内漏。其中浮动轴套与齿轮端面之间泄漏面积大，是造成内漏的主要部位。这部分漏损量占全部内漏的50%~70%左右。磨损内漏的齿轮泵其容积效率下降，油泵输出功率大大低于输入功率。其损耗全部转变为热能，因此会引起油泵过热。若将结合平面压紧，因工作时浮动轴套会有少量运动而造成磨损，结果使农具提升缓慢或不能提升，这样的浮动轴套必须更换或修理。CQJ-16
CQJ-25
CQJ-40
YJZQ-H10N
YJZQ-H50N
YJZQ-H32N
YJZQ-H20W
YJZQ-H25N
YJZQ-H40W
YJZQ-H15N
YJZQ-H10W,
VT5002-2X/R5E
VT5011/12-3X/R5E
VT5000-2X/R1E
VT5013-3X/R5E
VT5015-3X/R5E
VT5016-3X/R5EVT5017-3X/R5E
VT11382-1X/
VT3030-1X/
VT3031-1X/
VT3033-1X/
VT3034-1X/
VT3036-1X/
VT3037-1X/
VT13041-1X/
VT13005-1X/
VT11110-1X/
VT3017-3X/
VT3018-3X/
VT5066-1X/R1E
VT-VRM1-1-1X/
VT11122-1X/
VT11123-1X/
VT17128-1X/1