主动轴衬套孔与从动轴孔磨损的修理:主动轴衬套孔磨损后，可用铰削方法消除磨损痕迹，然后配用加大至相应尺寸的衬套。从动轴孔磨损也以铰削法消除磨损痕迹，然后按铰削后孔的实际尺寸配制从动轴NXQ2-L100/31.5-H
NXQ2-L150/31.5-H
蓄能器NXQ2-F0.25/10-H
NXQ2-F0.4/10-H
NXQ2-F0.63/10-H
蓄能器NXQ2-F1/10-H
NXQ2-F1.6/10-H
NXQ2-F2.5/10-H
蓄能器NXQ2-F4/10-H
NXQ2-F6.3/10-H
VT-VRPA1-527-1X/V0
VT-VRPA1-527-1X/V0/PV
VT-VRPA1-537-1X/V0/PV
VT-VRPA1-100-1X/V0/0
VT-VRPA1-150-1X/V0/0(2FRE6 )
VT-VRPA1-151-1X/V0/0 (2FRE10/16)
VT-SWKD-2-1X/V0/0
VT-SR42-1X/1/2
VT-SR42-1X/1/3
VT-KRRA2-537-2X/V0
VT-KRRA2-527-2X/V0/2
缙云A11VLO260LRDU2/11R-NZD12K84H-S VT-VRPA1-527-2X/V0/RTS-2STV
VT-MSPA1-525-1X/V0
VT-VSPA1K-1-1X/
VT-MSPA1-50-1X/V0/0-24
VT-MSPA1-50-1X/V001
VT-MSPA2-1-1X/V0/0
VT-MSPA2-200-1X/V0/0
VT3002-2X/48F
VT3002-2X/64G
http://www.qihuiwang.com/product/q35527/256297320.html VT-SSPA1-508-2X/V0
VT-SSPA1-508-2X/V0/I
VT-SSPA1-525-2X/V0
VT-SSPA1-50-1X/V0/0-24
VT-PVPQ1-1X/2R900070872
VT-VPCD-1-1X/V0/1-P-1
VT-VPCD-1-1X/V0/1-D-1
VT-VPCD-1-1X/V0/1-C-1
VT-VPCD-1-1X/V100/1-0-1
聊城A11VO40DRG/10R-NSC12K02-K

6.齿轮油泵停止工作时，应先将回油阀缓缓松开，待压力表慢慢回至零位后，方可卸开千斤顶的油管接头螺母。严禁在负荷时拆换油管或压力表等。NXQ1-L0.63/20-H
蓄能器NXQ1-L1/20-H
NXQ1-L1.6/20-H
NXQ1-L2.5/20-H
蓄能器NXQ1-L4/20-H
NXQ1-L6.3/20-H
NXQ1-L16/20-H
蓄能器NXQ1-L25/20-H
NXQ1-L40/20-H
NXQ1-L20/20-H
VT5002-2X/R5E
VT5011/12-3X/R5E
VT5000-2X/R1E
VT5013-3X/R5E
VT5015-3X/R5E
VT5016-3X/R5EVT5017-3X/R5E
VT11382-1X/
VT3030-1X/
VT3031-1X/
VT3033-1X/
VT3034-1X/
VT3036-1X/
VT3037-1X/
VT13041-1X/
VT13005-1X/
VT11110-1X/
VT3017-3X/
VT3018-3X/
VT5066-1X/R1E
VT-VRM1-1-1X/
VT11122-1X/
VT11123-1X/
VT17128-1X/1

7.配合双作用千斤顶的齿轮油泵，以采用两路同时输油的双联式齿轮油泵为宜。蓄能器NXQ1-L25/20-a―H
NXQ1-L40/20-a-H
NXQ1-L63/20-H
蓄能器NXQ1-L80/20-H
NXQ1-L100/20-H
NXQ1-L150/20-H
蓄能器NXQ1-L0.25/31.5-H
NXQ1-L0.4/31.5-H